CSA 60 unit, non-Locking, FAST charger rack

Storm Choke® K safety valves are ambient-type, wireline retrievable valves with the largest flow area of all direct controlled safety valves on the market. They are ideally suited for high-volume, low-pressure wells. These valves are normally closed and pre-charged with a set dome pressure. When the well flowing pressure drops below the predetermined dome-pressure charge because of a rupture in flowline or surface equipment, the dome pressure and main valve spring close the valve, shutting in the well below the earth’s surface. This valve contains a detent mechanism to provide a positive snap-action closure at the predetermined disaster rate of the valve. Its bore is not restricted by a flow bean. The valve is designed to resist pressure surges. A metal-to-metal poppet valve and seat comprise the valve’s primary closure mechanism. The K valve is ideal for protecting wells with declining bottomhole pressure. This valve closes in situations where a pressure decline would not activate a valve with a flow bean. To reopen the valve, the operator must fully equalize pressure either by applying pressure in the tubing from the surface or by an equalizing prong. The valve will reopen when the tubing pressure acting on the internal piston area overcomes the dome charge. Applications » Wells with declining bottomhole pressure » High-volume, low-pressure wells » Wells with no provisions for surface-controlled valves Features » Poppet closure » Large ports with capacity for high-volume wells » Designed to resist pressure surges *description excerpted from manufacturers catalogue.

The Super Spooler SUHT-25-2415 is designed for the heaviest of spooling loads in the most adverse conditions. Spooling units designed to ensure cables or control lines are kept in tension while running in or out of hole. Our spooling units are fully designed, manufactured and assembled with sheaves (half or full moon) to guide control, injection, or mono-conductor cable preventing damage while being tripped in hole. Units are available in pneumatic, hydraulic, or electric drive and are ATEX zone and DNV certified as required by location. Spooling units can also be equipped with a filling pump to monitor pressure while tripping – improving efficiency as a sudden pressure drop indicates line damage.

The T, T-CL, C-SRL-CL and CXS Tubing Hangers are all single completion, mandrel-type hangers for use in either the C Tubing Spool or the CD-2 Tubing Spool. T Tubing Hanger The T Tubing Hanger withstands stress of high pressure, corrosive/erosive elements associated with well flow. Its flexible neck maintains the metal seal despite thermal or pressure cycling. T-CL Tubing Hanger The T-CL Tubing Hanger withstands stress of high pressure, corrosive/erosive elements associated with well flow. A control line exit block is available in either a bull plug style or block needle valve style. C-SRL-CL Tubing Hanger The C-SRL-CL Tubing Hanger incorporates a pressure energized SRL neck seal which accommodates vertical movement in the tubing hanger during BOP testing. A control line exit block is available in either a bull plug style or block needle valve style. The C-SRL-CL hanger should be used in 7-1/16” 10,000 psi Type C Tubing Spools. CXS Tubing Hanger The CXS Tubing Hanger includes two neck seals which may be used to isolate one control line.

Ensuring Production Integrity with InWaTec Combined's E-Line Tubing Inspection Services In the lifecycle of oil and gas wells, tubing integrity is fundamental to ensuring consistent production and operational safety. At InWaTec Combined, we offer specialized E-Line Tubing Inspection Services to preemptively identify and mitigate risks associated with tubing failure, utilizing state-of-the-art diagnostic techniques to safeguard your assets. Tubing failures, which can stem from deformation, physical wear, or corrosion, pose a significant threat to well integrity and production. Our advanced inspection services are designed to detect these issues early, enabling timely interventions that maintain continuous well performance. Our comprehensive suite of E-Line Tubing Inspection Services includes: Cased-Hole Calipers: These tools provide precise measurements of the internal diameter of tubing, detecting anomalies and changes that could indicate deformation or wear. Flux-Leakage Tools: Specialized for identifying defects in ferrous tubulars, these tools locate areas of metal loss or corrosion by detecting disruptions in magnetic flux. Electromagnetic Phase-Shift Tools: By measuring the changes in electromagnetic fields, these tools can effectively pinpoint areas of wall thickness changes due to corrosion or wear. Ultrasonic Tools: Employing high-frequency sound waves, these tools are adept at measuring tubing wall thickness, identifying areas at risk of thinning, which could lead to potential collapse. In addition to these, our E-Line Tubing Inspection Services also employ ultrasonic radial-cement-evaluation and modified openhole-imaging devices, which are particularly effective in assessing the condition of the tubing for signs of internal or external metal loss—a crucial step in preventing unexpected well shut-ins. At InWaTec Combined, we understand that the stakes are high when it comes to maintaining well integrity. Our E-Line Tubing Inspection Services are not just about identifying problems; they're about delivering peace of mind. By utilizing our advanced diagnostic tools, operators can rest assured that the integrity of their production tubing is being monitored with the utmost precision, allowing them to focus on maximizing output and efficiency. Choosing InWaTec Combined means partnering with a company that places a premium on innovation, safety, and reliability. Our commitment to excellence ensures that your operations benefit from the latest in inspection technology, delivered by a team of seasoned professionals. Trust us to provide the insights you need to keep your wells flowing safely and smoothly, today and into the future.

ELEKS: Empowering Energy Excellence through Automated Drone-Powered Inspections In the dynamic world of energy, innovation is the driving force behind success. ELEKS stands at the forefront of this innovation, leveraging our unparalleled energy sector technology expertise to revolutionize the way you manage your assets, commercial buildings, and industrial facilities. Imagine a future where automated drone-powered inspections redefine efficiency, dramatically reducing costs, assessment time, and workplace hazards, all while making a significant contribution to lowering carbon emissions. Our approach integrates cutting-edge technology with precision, creating custom solutions that redefine the limits of what's possible. Here's how ELEKS can be your partner in achieving operational excellence. 1. Efficient Inspections, Reduced Costs: With automated drone-powered inspections, the cost-efficiency of your operations skyrockets. Manual inspections involve substantial expenses, but our technology-driven approach slashes costs while enhancing accuracy. 2. Swift Assessment: Time is of the essence in the energy sector. Our solutions redefine assessment timelines, making inspections at least ten times faster than traditional human-based methods. 3. Workplace Safety Revolution: Workplace hazards are a critical concern. By utilizing automated drones, you eliminate the risks associated with manual inspections, creating a safer work environment for your teams. 4. Carbon Emission Reduction: In an era focused on sustainability, carbon emissions reduction is a priority. Our automated inspections not only streamline operations but also contribute to lowering carbon emissions, showcasing your commitment to a greener future. 5. High-Precision Imagery: Augmented with high-precision cameras, our fully automated aerial vehicles (UAVs) capture high-resolution images with sub-millimeter accuracy. This level of precision empowers you with detailed insights for informed decision-making. 6. Versatile Operational Environment: Our automated drones operate effectively even in GPS-denied environments. This adaptability ensures that you can collect valuable data, regardless of the setting. 7. Data-Powered AI and ML: The data collected from automated inspections becomes a goldmine for AI and machine learning solutions. Our technology empowers you to leverage insights, enhancing risk management and operational efficiency. ELEKS: Transforming Energy Operations ELEKS doesn't just offer services – we offer transformation. Our energy sector technology expertise isn't just about solutions; it's about redefining industry standards. The convergence of cutting-edge technology, precision, and sustainability underpins our approach. Join us in reshaping the future of energy operations, where innovation meets efficiency, safety is paramount, and sustainability is more than a buzzword. With ELEKS by your side, you're not just embracing technology – you're embracing a journey towards operational excellence. Step into a world where automated drone-powered inspections become the cornerstone of efficient, safe, and sustainable energy management.

Enhance Your Product Labeling with Labelling Machine Leasing from CWB National Leasing Revolutionizing Your Packaging Process with Advanced and Flexible Equipment Solutions In the competitive world of retail and manufacturing, having efficient and reliable labelling machines is crucial for maintaining product integrity and brand consistency. Leasing labelling machines through Canadian Western Bank (CWB) National Leasing offers a flexible, cost-effective, and practical solution for businesses looking to improve their packaging process. Here’s how leasing labelling machines can benefit your business: 1. Quick Access to Advanced Labelling Technology CWB National Leasing understands the need for efficient packaging solutions in your business. They offer a fast leasing process, typically notifying your equipment dealer about payment within 48 hours of approval. This efficiency ensures that your labelling machines can be delivered and operational quickly, enhancing your production line and reducing packaging bottlenecks. 2. Increased Financial Flexibility Leasing labelling machines with CWB National Leasing enhances your buying power. It allows you to spread costs over manageable periodic payments instead of a significant upfront purchase, freeing up capital for other essential business operations. The option to add extra features or accessories to your labelling machines for a small payment increase enables customization to meet specific packaging needs. 3. Effective Cash Flow Management Manageable lease payments over the term mean your labelling machines start contributing to your business’s revenue while they're being paid off. This strategy helps maintain a balanced expense-to-revenue ratio, crucial for business growth and financial stability. 4. Customizable Payment Plans CWB National Leasing offers a variety of payment options, including seasonal, semi-annual, or annual plans, tailored to your business’s financial cycle. This flexibility is especially beneficial for businesses with seasonal variations in demand, ensuring that payments are practical and fit your financial situation. 5. Potential Tax Benefits Leasing labelling machines can offer tax advantages, such as the ability to expense lease payments instead of capitalizing the cost of the equipment. Consulting with a tax advisor is advisable to understand how leasing can positively impact your business’s tax position. Conclusion Opting to lease labelling machines through CWB National Leasing is a strategic decision that equips your business with essential packaging tools while maintaining financial agility. It ensures access to high-quality labelling technology, vital for efficient product packaging and branding, without the financial strain of a large upfront investment. This leasing approach enables enhanced operational efficiency, improved packaging quality, and increased competitiveness in the market, helping your business thrive in today’s dynamic business environment.

Introducing the WISE LITE 2: The Ultimate Cordless Miner's Cap Lamp from Provix Provix is proud to unveil the WISE LITE 2, a superior cordless miner's cap lamp designed for the rigorous demands of the mining industry. Combining cutting-edge technology with the highest safety standards, the WISE LITE 2 is an essential piece of equipment for any miner. Exceptional Lighting Performance The WISE LITE 2 is equipped with a high-capacity 7,000mAh battery, offering a continuous discharging time of 16 hours. This ensures long-lasting illumination for extended work periods. The main light has a working voltage of 3.0V, a current of 400 mA, and a power of 1.2W, producing a luminous flux of 167 lumens. With an initial lighting degree of 8,500 Lux, it provides excellent visibility in the darkest environments. Built to Last Durability is key in mining equipment, and the WISE LITE 2 stands out in this aspect. It boasts a main light life span of 50,000 hours and an auxiliary light life span of 40,000 hours. The battery life extends to 1,200 cycles under reasonable working conditions, highlighting its reliability and longevity. Safety and Compliance Safety is a top priority, and the WISE LITE 2 meets the highest safety standards. It is explosion-proof, MSHA certified, and has an IP68 waterproof rating. The short circuit protection time of less than 320μs ensures additional safety in hazardous conditions. Ergonomic and Convenient Design The WISE LITE 2 is designed for comfort and ease of use. Weighing just 169g (5.96 oz) and measuring 84x69x50mm (3.3x2.7x2.0in), it is compact and lightweight, making it ideal for long shifts. The quick charging time of 4 hours means it’s ready to go when you are. Versatile for Various Applications While designed for mining, the WISE LITE 2 is also suitable for a variety of other applications such as construction, emergency rescue, outdoor adventures, and more, offering versatility and dependability in any setting. Get Your WISE LITE 2 Today Elevate your mining operations with the reliable, efficient, and safe WISE LITE 2. Available now at Provix, this cordless miner's cap lamp is the solution for advanced lighting in challenging environments. Visit www.provix.net for more details or to make a purchase.

The Lufkin Conventional Crank Balanced Pumping Unit, widely known and accepted, is the old reliable “Work Horse” of the oil patch. This is the most universally adaptable unit in the Lufkin line. These units are simple to operate and require minimum maintenance. Unit Size* C-1824D-305-240 A 120.00 B 228.00 C 340.00 E 263.50 F 396.50 H 545.00 I 25.50 J 110.00 L 64.00 M 80.25 N - N1 24.50 R 161.00 T 58.88 U 92.38 V 52.00 W 50.00 X 112.50 AA 51.69 AB 90.88 UU 24.13 VV 57.00 In addition to being the world’s leading manufacturer and supplier of sucker rod pumping units, Lufkin Oilfield Services refurbishes and sells used pumping units and provides installation, field service, machine shop repair and new OEM parts for its’ customers. All brands – Lufkin, Churchill, American, LeGrand, Bethlehem, National, etc. – are supported. Additionally, Lufkin Automation is the industry leader in oil production automation and well optimization products and services (pump-off controllers, dynamometers, fluid level equipment, well analysis, design/analysis software, well design consulting and training). With the acquisition of Delta-X and Nabla and with thousands of controllers in service, Lufkin Automation continues the Lufkin tradition of helping producers lower their production costs and optimize well efficiency.

Quick Absorbent Pads stand as a reliable and efficient solution for liquid cleanup, offering a combination of rapid absorption, fine-fiber construction, oil-specific capabilities, durability, and enhanced visibility. Upgrade your cleanup processes with a product designed to keep surfaces dry and operations running. Choosing the right solution for your needs is crucial, and our Quick Absorbent Pads offer several advantages that set them apart from other options. Why should you use the absorbent pads? Absorbent pads are specifically designed for rapid absorption of leaks, spills, and overspray. The quick response time is crucial in preventing the spread of liquids and minimizing potential hazards. If time efficiency is a priority, our absorbent pads are a superior choice. Unlike some general-purpose absorbents, our pads are engineered for the selective absorption of oils and oil-based liquids. This targeted approach ensures maximum effectiveness in scenarios where oil contamination is a primary concern. If your application involves oil cleanup, our pads offer a specialized solution. The fine-fiber construction of our absorbent pads ensures a clean and residue-free surface after cleanup. This is a significant advantage over some absorbents that may leave behind liquid or fiber remnants. If you value a thorough and residue-free cleanup, our absorbent pads are the ideal choice. absorbent pads feature a durable multi-layer polypropylene fiber structure, making them tough and resistant to tearing. This robust construction ensures longevity and reliability, even in demanding industrial environments. If durability and tear resistance are priorities, our absorbent pads excel in these aspects. The oil-specific absorption feature of our pads means they do not absorb water. This specificity is crucial in scenarios where water contamination is not desired. If you require an absorbent that selectively targets oils without absorbing water, our pads provide a distinct advantage. The bright white color of our absorbent pads enhances visibility during cleanup operations. This makes it easier to monitor the saturation level and determine when replacement is needed. If visibility and ease of use are important considerations, our pads offer a practical solution. Quick Absorbent Pads are versatile and suitable for a wide range of industries and applications. Whether you're in manufacturing, automotive, or any other sector with liquid spill concerns, our pads offer a reliable and efficient solution. In short: Oil Only Absorbent Pad - Absorbs up to 0.3 L (0.07 gal), absorbs rapidly, selective absorption of oils and oil-based liquids with maximum effectiveness, No residue or fiber left behind, the absorbent pad has durable multi-layer construction, oil-selective without absorbing water, bright white color for visibility, versatility across industries. Technical Specs Part Number: OH-P811 Product Type: Absorbent Pad Fluids Absorbed: Oil Based Liquids Volume Absorbed per unit: 17.5 oz Colour/Pattern: White Outside Skin Material: Polyester Rope Along Length: No Volume Absorbed per pkg.: 5.2 liter Floating: Yes UV Resistant: No Size: 8” x 11.5” Filler Material: Polypropylene Filler Flame Resistant: No Incinerable: Yes

Introducing the SFF Surface Filter from Marlin Oil Tools: The Ultimate Solution for Protecting Your Downhole Equipment Marlin Oil Tools is proud to offer the SFF Surface Filter, a highly efficient tool designed to safeguard your downhole equipment by filtering mechanical particles from the liquid flow. Engineered with precision, the SFF Surface Filter is an essential addition to any oil and gas operation, ensuring the longevity and reliability of your valuable downhole tools. Key Features of the SFF Surface Filter: Advanced Filtration Technology: Utilizes a wire wound welded to the frame, creating gaps smaller than the permissible size of particles, thereby capturing and retaining mechanical impurities as the liquid flows through. Customizable Filtration Levels: Offers versatile filtration options with membrane fineness primarily available in 0.25 mm, 0.5 mm, and 0.9 mm, allowing operators to select the appropriate level of filtration for their specific well conditions. Durable and Reliable Design: Crafted for durability and long-term use, the SFF Surface Filter stands up to the demanding conditions of oil and gas extraction environments. Protects Sensitive Downhole Tools: Especially beneficial for tools that are highly sensitive to mechanical impurities, such as downhole mud motors with Metal-to-Metal power sections and downhole gas separators. Easy Installation: Designed for straightforward installation in the pipeline running from the pump to the well, ensuring seamless integration into your existing workflow. Enhanced Operational Efficiency: By preventing mechanical particle contamination, the SFF Surface Filter contributes to the smooth operation and reduced maintenance needs of downhole equipment, ultimately saving time and costs. Elevate the protection and efficiency of your oil and gas operations with the SFF Surface Filter from Marlin Oil Tools, a premier downhole tool solution engineered to filter mechanical particles from liquid flows. Featuring advanced filtration technology and customizable filtration levels, the SFF Surface Filter is designed to meet the rigorous demands of the oil and gas industry, ensuring the protection and longevity of sensitive downhole equipment. Whether you're dealing with downhole mud motors, gas separators, or other critical tools, the SFF Surface Filter offers a reliable, durable, and easy-to-install solution to maintain clean liquid flows and enhance operational efficiency. Opt for the SFF Surface Filter and invest in the safety and productivity of your downhole operations. Why Choose the SFF Surface Filter from Marlin Oil Tools? Superior Protection: Provides unmatched filtration to protect downhole equipment from mechanical impurities. Operational Versatility: Adaptable to a wide range of oil and gas operations with customizable filtration to suit diverse needs. Long-lasting Durability: Built to withstand the harsh conditions of oil and gas extraction, ensuring reliability and longevity. Cost-Efficient Maintenance: Reduces the need for frequent downhole tool maintenance, saving both time and operational costs. The SFF Surface Filter by Marlin Oil Tools represents the forefront of filtration technology in the oil and gas industry, providing a vital solution for maintaining the integrity and efficiency of your downhole equipment. Choose the SFF Surface Filter for an enhanced level of protection and operational excellence in your well interventions.

Elevate Downhole Efficiency with HOCA Oil Tools' Plug Chokes for Tubing In the rapidly evolving landscape of the oil and gas industry, achieving optimal control and efficiency in downhole operations is crucial. HOCA Oil Tools, at the forefront of downhole technology innovation, introduces its Plug Chokes for Tubing – specialized tools designed to revolutionize fluid flow control within the wellbore. Crafted with precision and built to meet the highest industry standards, our Plug Chokes are engineered to enhance the performance and safety of downhole operations. HOCA’s Plug Chokes for Tubing: Precision Control, Unmatched Durability Our Plug Chokes for Tubing are designed for operators who demand precise fluid flow control in their downhole operations. These tools are crucial for managing production rates, minimizing fluid losses, and optimizing well performance. Constructed from high-grade materials resistant to corrosion and wear, HOCA's Plug Chokes ensure reliability and durability under the harshest downhole conditions. Experience the HOCA Oil Tools Advantage Opting for HOCA Oil Tools’ Plug Chokes for Tubing means choosing a solution that stands for innovation, efficiency, and reliability. Our commitment to excellence ensures that our products not only meet but exceed the demands of modern oilfield operations, providing our clients with tools that enhance their downhole success. Integrating our Plug Chokes into your downhole operations marks a step toward enhanced efficiency, safety, and cost-effectiveness. With HOCA Oil Tools, you gain more than just a supplier; you gain a strategic partner committed to supporting your operational challenges with advanced solutions and comprehensive service. Choose HOCA Oil Tools for your downhole needs and unlock the full potential of your operations with our Plug Chokes for Tubing. Partner with us, and take your downhole operations to new heights of efficiency and performance. With HOCA Oil Tools, empower your downhole activities with tools that set new standards for reliability, control, and performance in the challenging oil and gas industry.

Advance Your Manufacturing Capabilities with Milling Machine Leasing from CWB National Leasing Transforming Your Production Processes with Flexible and Efficient Equipment Solutions In the manufacturing, metalworking, and engineering sectors, milling machines are indispensable for precise material shaping and fabrication. Leasing milling machines through Canadian Western Bank (CWB) National Leasing offers a flexible, cost-effective, and practical solution for businesses seeking to enhance their production capabilities. Here’s how leasing milling machines can benefit your business: 1. Quick Access to Advanced Manufacturing Equipment CWB National Leasing understands the importance of maintaining an efficient production line. They offer a swift leasing process, typically providing decisions within 48 hours of application submission. This ensures that your milling machines can be delivered and operational quickly, minimizing downtime and enhancing your manufacturing efficiency. 2. Enhanced Financial Flexibility Leasing milling machines with CWB National Leasing boosts your buying power. It enables you to free up capital by opting for manageable periodic payments instead of a large upfront purchase. The option to add extra features or accessories to your milling machines for a small payment increase allows for customization to meet specific production requirements. 3. Effective Cash Flow Management Smaller lease payments over the term mean your milling machines start contributing to your business’s revenue while they're being paid off. This approach helps maintain a healthy balance between expenses and income, crucial for the financial stability and growth of your business. 4. Customizable Payment Plans CWB National Leasing offers various payment options, including seasonal, semi-annual, or annual plans, tailored to your business’s financial cycle. This flexibility is especially beneficial for businesses with variable or seasonal income, ensuring that payments are practical and fit your financial situation. 5. Potential Tax Benefits Leasing milling machines can offer tax advantages, such as the ability to expense lease payments instead of capitalizing the cost of the equipment. Consulting with a tax advisor is advisable to understand how leasing can positively impact your business’s tax position. Conclusion Opting to lease milling machines through CWB National Leasing is a strategic decision that equips your business with essential manufacturing equipment while maintaining financial agility. It ensures access to high-quality milling machines, vital for precise and efficient production, without the financial strain.

Power Up Your Projects: Generator Set Leasing with CWB National Leasing Fuel Your Business Growth with Smart Equipment Leasing Solutions In the construction and industrial sectors, reliable power is non-negotiable. Generator sets play a crucial role in ensuring your operations run smoothly. Leasing your generator sets through Canadian Western Bank (CWB) National Leasing offers a flexible, financially smart solution that caters to your business needs. Here’s how leasing generator sets can energize your business operations: 1. Quick Equipment Access CWB National Leasing values your time and project deadlines. They ensure a swift review and decision on your lease application, typically notifying your equipment dealer about the payment within 48 hours of approval. This quick turnaround means you can have your generator sets delivered and operational promptly, minimizing any project delays. 2. Increased Financial Leverage Leasing with CWB National Leasing enhances your purchasing power. It enables you to acquire essential generator sets through manageable periodic payments rather than a significant upfront cost. This approach frees up capital for other business areas, and you can even add extra features or accessories to your generator sets with a slight increase in payments. 3. Optimized Cash Flow Management Manageable lease payments spread out over time mean your generator sets start contributing to your revenue even as you pay for them. This strategy helps maintain a healthy balance between your expenses and income, crucial for business stability and growth. 4. Flexible Payment Options CWB National Leasing offers tailored payment plans, including seasonal, semi-annual, or annual options, to match your business's revenue cycle. This flexibility is particularly beneficial for businesses with fluctuating income, ensuring payments align with your financial flow. 5. Potential Tax Advantages Leasing may provide tax benefits, as it allows you to expense lease payments rather than depreciating the capital cost of the generator sets. Consulting with a tax advisor can help you understand how leasing can optimize your business’s tax situation. Conclusion Choosing to lease your generator sets through CWB National Leasing is a strategic decision that equips your business with the necessary power infrastructure while maintaining financial agility. It ensures that you have the power support you need for your projects without the burden of a large upfront investment, paving the way for efficient operations, growth, and profitability in the demanding construction and industrial landscapes.

Geotechnical drilling is a method of investigating subsurface soils to provide data for engineering design prior to construction of buildings, dams, roadways and other infrastructure sites. The low impact and maneuverability of the geotechnical drilling rigs allow for free movement on geotechnical investigation sites with limited access, such as next to foundations, inside buildings, or under power lines. Use the centerline head side shift on our geotechnical drill rigs to simplify traditional geotech techniques such as: Augering Mud rotary SPT Shelby tubes Hard rock cores CPT

The Oil-Only Absorbent Pillow, represented by the OH-PI1212, emerges as a utilitarian solution. From the versatile material known as polypropylene, this unassuming pillow bears the capacity to redefine the efficiency and sustainability of liquid cleanup. Why is Polypropylene chosen as the material for use? Polypropylene is a preferred material for oil-based cleanup for several reasons, making it an ideal choice for products like the Oil-Only Absorbent Pillow. Hydrophobic Nature Polypropylene is inherently hydrophobic, meaning it repels water. This characteristic is crucial in oil-based cleanup scenarios where the goal is to selectively absorb oils while avoiding the absorption of water. The hydrophobic nature of polypropylene ensures that the material remains focused on its primary task—absorbing oil-based liquids. High Affinity for Oil Polypropylene has a high affinity for oil-based substances. When in contact with oils, polypropylene quickly absorbs and retains these liquids. This property enhances the efficiency of cleanup operations, allowing for the rapid containment and absorption of oil spills. Lightweight and Durable Polypropylene is a lightweight yet durable material. This is advantageous in cleanup products like absorbent pillows, as it ensures ease of handling and deployment while maintaining structural integrity during use. The lightweight nature makes these products practical and user-friendly in various industrial settings. Chemical Resistance Polypropylene is known for its chemical resistance, providing stability when exposed to a wide range of substances, including oils and hydrocarbons. This resistance ensures that the material remains effective and does not break down when encountering various oil-based liquids. Recyclability Polypropylene is recyclable, adding an environmentally conscious aspect to its use in oil-based cleanup products. The ability to recycle polypropylene helps reduce the overall environmental impact by promoting the responsible disposal and reuse of materials. Cost-Effectiveness Polypropylene is a cost-effective material, contributing to the affordability of products designed for oil-based cleanup. Inert Nature Polypropylene is inert, meaning it does not react with or alter the composition of the substances it meets. This inert nature is crucial in cleanup situations where the goal is containment and absorption without introducing additional complications or reactions. Where is the Oil-Only Absorbent Pillow typically used? • Industrial facilities • Marine environment • Construction sites • Oil refineries • Emergency response • Environmental cleanup projects • Agricultural operations • Transportation Technical Specifications Part Number: OH-PI1212 Product Type: Absorbent Pillow Fluids Absorbed: Oil Based Liquids Volume Absorbed per unit: 1.35 gal Colour/Pattern: White Outside Skin Material: Polyester Rope Along Length: No Volume Absorbed per pkg.: 6.7 gal Floating: Yes UV Resistant: No Size: 12” x 12” Filler Material: Polypropylene Filler Sock/Boom Profile: Square Flame Resistant: No Incinerable: Yes

Elevate Your Textile Business with Embroidery Machine Leasing from CWB National Leasing Transforming Your Creative Ventures with Flexible and Cost-Effective Solutions In the dynamic world of textile and garment production, embroidery machines are pivotal for adding value and uniqueness to products. Leasing embroidery machines through Canadian Western Bank (CWB) National Leasing offers a strategic and financially astute solution for businesses looking to expand their embroidery capabilities. Here’s how leasing embroidery machines can enhance your textile business: 1. Rapid Equipment Access CWB National Leasing values the pace and efficiency of your business. They offer a fast and streamlined leasing process, with decisions typically made within 48 hours of application submission. This swift turnaround ensures that your embroidery machines can be delivered and operational quickly, keeping your production line active and efficient. 2. Enhanced Financial Flexibility Leasing embroidery machines with CWB National Leasing increases your purchasing power. Opting for periodic payments over a large upfront purchase helps free up capital for other crucial business operations. Additionally, the flexibility to add extra features or accessories to your machines for a small payment increase enables customization to meet your specific production requirements. 3. Effective Cash Flow Management With manageable lease payments spread over the term, your embroidery machines begin contributing to your business’s revenue while they are still being paid off. This approach helps maintain a healthy balance between expenses and revenue, which is essential for business growth and stability. 4. Customizable Payment Plans CWB National Leasing offers a variety of payment options, including seasonal, semi-annual, or annual plans, tailored to align with your business’s financial cycle. This flexibility is particularly beneficial for businesses with seasonal fluctuations in income, ensuring that payments are practical and aligned with your financial situation. 5. Potential Tax Advantages Leasing embroidery machines can offer tax benefits, such as the ability to expense lease payments instead of capitalizing the cost of the equipment. Consulting with a tax advisor is advisable to explore how leasing can positively impact your business’s tax position. Conclusion Choosing to lease embroidery machines through CWB National Leasing is a strategic decision that equips your textile business with advanced equipment while maintaining financial agility. It ensures access to state-of-the-art embroidery machines, vital for producing high-quality, detailed designs, without the financial burden of a large upfront investment. This leasing approach enables enhanced operational efficiency, increased production capacity, and greater profitability, helping your business to thrive in the competitive textile industry.

Guarding the Pulse of Your Operations with Nulux’s Network Maintenance Services Navigating through the unyielding terrain of the Oil and Gas industry demands not merely a communication network that is robust but one that stands unassailable against the test of time and operational strain. For professionals who engineer the vitality of our energy sector, ensuring that every node, every link, and every byte of data pulsates without falter through your networks is paramount. Herein lays the essence of Nulux Network Solutions’ pristine Network Maintenance services. Catalyzing Sustainability through Robust Network Health With a relentless devotion to facilitating an unobstructed flow of products, solutions, and services across the complete energy value chain, Nulux is unwaveringly committed to escorting our customers on the voyage towards a future where sustainability and operational excellence coalesce seamlessly. In the domain of Fiber Optic communication, where the tiniest of signal attenuations can cascade into significant operational impediments, maintaining the unyielding health of your network becomes imperative. And this is where our Network Maintenance services shine, illuminating your operations with the assurance of unbroken, reliable connectivity. Embracing Nulux’s Network Maintenance: A Fortification of Reliability Aligning with Nulux’s Network Maintenance services infuses your operations with: Proactive Safeguarding: Our technical mavens, with a fine-tuned acumen honed by over two decades in the industry, provide proactive monitoring and mitigation strategies, ensuring that potential issues are neutralized before they can reverberate through your operations. 24/7 Vigilance: In an industry where every second is critical, our 24/7 monitoring and support stand as your unwavering sentinel, ensuring that come what may, your network's integrity remains unassailable. Bespoke Maintenance Protocols: Our network maintenance solutions are not generic but are meticulously tailored to resonate with the specificities of your operations, ensuring that our maintenance protocols echo with the unique requirements of your network architecture. Minimized Downtime: With an arsenal of cutting-edge diagnostic tools and an experienced team that specializes in rapid response and resolution, we ensure that any potential downtimes are not merely addressed but are minimized to a negligible whisper. Embarking on an Uninterrupted Operational Journey with Nulux At Nulux Network Solutions, our network maintenance services go beyond mere problem resolution; we dive into the very fabric of your communication networks, ensuring that every fiber, every connection, and every data transmission is enveloped in a cocoon of reliability and unyielding operational excellence. In an industry where data transmission is as vital as the energy being harnessed, Nulux stands as your partner, ensuring that the pulse of your operations, your communication networks, perpetually remain vibrant, secure, and impeccable. Choose Nulux, and navigate through your operational journey with the assurance that the lifelines of your communication are not merely maintained but are guarded, fortified, and optimized, ensuring every operational heartbeat is steady, uninterrupted, and perpetually resilient.

Boost Your Business Efficiency with Printer Leasing from CWB National Leasing Revolutionizing Your Document Handling with Flexible and Advanced Printing Solutions In the modern business landscape, having access to high-quality printers is essential for efficient document management and communication. Leasing printers through Canadian Western Bank (CWB) National Leasing offers a flexible, cost-effective, and practical solution for businesses looking to enhance their printing capabilities. Here’s how leasing printers can benefit your business: 1. Fast Access to High-Performance Printers CWB National Leasing recognizes the importance of advanced printing technology in your business operations. They offer a quick leasing process, with decisions typically made within 48 hours of application submission. This ensures that your printers can be delivered and operational quickly, enhancing your productivity and meeting your document handling needs promptly. 2. Increased Financial Flexibility Leasing printers with CWB National Leasing enhances your buying power. It allows you to free up capital by opting for periodic payments over a substantial upfront purchase. The flexibility to add extra features or accessories to your printers for a small payment increase allows for customization to meet specific business requirements. 3. Effective Cash Flow Management Manageable lease payments over the term mean your printers start contributing to your business’s efficiency while they're being paid off. This approach helps maintain a balanced expense-to-revenue ratio, which is crucial for long-term business stability and growth. 4. Customizable Payment Plans CWB National Leasing offers various payment options, including seasonal, semi-annual, or annual plans, tailored to your business’s financial cycle. This flexibility is particularly beneficial for businesses with seasonal variations in revenue, ensuring that payments are practical and fit your financial situation. 5. Potential Tax Benefits Leasing printers can offer tax advantages, such as the ability to expense lease payments instead of capitalizing the cost of the equipment. Consulting with a tax advisor is advisable to understand how leasing can optimize your business’s tax position. Conclusion Opting to lease printers through CWB National Leasing is a strategic decision that provides your business with essential printing equipment while maintaining financial agility. It ensures access to state-of-the-art printers, vital for efficient and high-quality document production, without the financial burden of a large upfront investment. This leasing approach enables enhanced operational efficiency, improved document quality, and increased productivity, contributing significantly to the success and growth of your business in a competitive market.

SSG Consulting is a Project, Engineering and Construction Management Consulting firm, specializing in the implementation of Business and Project Management solutions on Mega projects in various industries. - Authorised KEY360 channel partner Our services cover the following: - Project Advisory & Audits - EMPCM Execution - Specialist Project Controls & Forensics - Project Digitalisation - Project Resourcing - Analytics & Dashboarding Our Track Record: - 25 BILLION MANAGED VALUE - 300 MILLION PLATFORM TRANSACTIONS - 80 DEDICATED STAFF - 10X BUSINESS PROCESSES IMPROVEMENT

Poseidon Robotics' Custom Lift Points: Unparalleled Strength for Your Subsea Lifting Needs When it comes to subsea operations, lifting heavy loads with precision and safety is a paramount concern. At Poseidon Robotics, we are proud to introduce our state-of-the-art Custom Lift Points—a breakthrough in subsea lifting technology. Engineered for exceptional strength and load-bearing capabilities, our Custom Lift Points are built to withstand the most challenging underwater lifting tasks. Strength Meets Customization At Poseidon Robotics, we understand that no two subsea projects are the same. That's why our Custom Lift Points are designed with versatility and customization in mind. We work closely with you to tailor our lift points to your specific requirements, ensuring that they seamlessly integrate with your subsea equipment, ROVs, or other subsea systems. Load Tested to Perfection Safety is at the core of everything we do at Poseidon Robotics. Our Custom Lift Points undergo rigorous load testing to ensure they exceed industry standards and can handle immense weights with ease. Rest assured that our lift points are reliable and dependable, giving you peace of mind during critical lifting operations. A Robust Solution for All Environments Subsea environments can be harsh and unforgiving, but our Custom Lift Points are up to the challenge. Crafted from high-quality materials, our lift points offer excellent corrosion resistance, making them suitable for prolonged underwater use without compromising on strength and performance. Versatility and Adaptability Whether you're dealing with offshore installations, subsea construction, or scientific research, our Custom Lift Points adapt to diverse applications. Their flexible design allows for easy integration into various subsea equipment and systems, giving you the freedom to tackle a wide range of projects efficiently. A Commitment to Excellence Poseidon Robotics takes pride in our commitment to excellence. Our team of experienced engineers and technicians ensures that each Custom Lift Point is meticulously crafted to meet the highest standards of quality and reliability. We leave no stone unturned in delivering lifting solutions that empower your subsea operations. Experience the Power of Poseidon Robotics' Custom Lift Points Embrace a new era of subsea lifting with Poseidon Robotics' Custom Lift Points. With unbeatable strength, unmatched customization, and unwavering safety, our lift points redefine what's possible beneath the waves. Join the Poseidon Robotics Revolution Unlock the potential of your subsea projects with Poseidon Robotics as your trusted partner. Our Custom Lift Points, load tested to an astounding 55,000 lbs, are here to elevate your subsea lifting capabilities to new heights. Discover the Future of Subsea Lifting Take the next step in your subsea journey with Poseidon Robotics. Contact us today to explore the possibilities of our Custom Lift Points and embark on a transformative subsea lifting experience. At Poseidon Robotics, we lift the world below the surface.